user convenience only and is not intended to alter agency intent N76 For materials of not more than 25 percent active ingredient by weight, packages consisting of inner metal packagings not greater than 250 mL (8 ounces) capacity each, packed in strong outer packagings together with sufficient absorbent material to completely absorb the liquid contents are authorized and need not conform to the requirements of part 178 of this subchapter. B44 All parts of valves and safety relief devices in contact with lading must be of a material which will not cause formation of acetylides. g. The test results shall be documented, shall be traceable, and shall be made available to a representative of the Department upon request. 111 Explosive substances of Division 1.1 Compatibility Group A (1.1A) are forbidden for transportation if dry or not desensitized, unless incorporated in a device. d. Receptacles containing adsorbed or absorbed ammonia shall meet the following conditions: (1) Receptacles shall be made of a material compatible with ammonia as specified in ISO 11114-1:2012(E) and ISO 11114-1:2012/Amd 1:2017(E) (IBR, see 171.7 of this subchapter); (2) Receptacles and their means of closure shall be hermetically sealed and able to contain the generated ammonia; (3) Each receptacle shall be able to withstand the pressure generated at 85 C (185 F) with a volumetric expansion no greater than 0.1%; (4) Each receptacle shall be fitted with a device that allows for gas evacuation once pressure exceeds 15 bar (1500 kPa) without violent rupture, explosion or projection; and. (3) Damage to terminals. 129 These materials may not be classified and transported unless authorized by the Associate Administrator on the basis of results from Series 2 Test and a Series 6(c) Test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport. 420 This entry does not apply to manufactured articles (such as table tennis balls). 4 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone D (see 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. Any glass inner packaging showing evidence of leakage, distortion or other defect under this test must not be transported under the terms of this special provision; b. For all modes of transportation, a written report submitted, retained, and updated in accordance with 171.16 is required if a fire, violent rupture, explosion or dangerous evolution of heat occurs as a direct result of a dry battery or battery-powered device. b. Lithium batteries conforming to paragraph a. of this special provision must be assigned to UN Nos. For transportation by aircraft, cargo transport units may only be offered for transportation and transported under conditions approved by the Associate Administrator. In making this determination factors to be taken into consideration include, but are not limited to, the capacity and geometry of the packaging and the effect of any insulation present, the temperature of the material when offered for transport, the duration of the journey, and the ambient temperature conditions typically encountered in the journey (considering also the season of year), the effectiveness and other properties of the stabilizer employed, applicable operational controls imposed by regulation (e.g., requirements to protect from sources of heat, including other cargo carried at a temperature above ambient) and any other relevant factors. The proper shipping name Paint related material may be used for consignments of packages containing Paint and Paint related material in the same package; b. Filling limits must be in accordance with portable tank special provision TP3. If you have questions or comments regarding a published document please These special provisions are in addition to the standard packaging requirements. Each B55 Water-tight, sift-proof, closed-top, metal-covered hopper cars, equipped with a venting arrangement (including flame arrestors) approved by the Associate Administrator are also authorized. When portable tank instruction T75 is referenced in Column (7) of the 172.101 Table, the applicable refrigerated liquefied gases are authorized to be transported in portable tanks in accordance with the requirements of 178.277 of this subchapter. A9 For combination packagings, if plastic bags are used, they must be packed in tightly closed metal receptacles before packing in outer packagings. During the course of transportation, these substances must be shaded from direct sunlight and all sources of heat and be placed in adequately ventilated areas. 30 Sulfur is not subject to the requirements of this subchapter if transported in a non-bulk packaging or if formed to a specific shape (for example, prills, granules, pellets, pastilles, or flakes). Radiation detectors transported as individual components must be transported as follows: (1) They must be packed in a sealed intermediate plastic liner with sufficient absorbent or adsorbent material to absorb or adsorb the entire gas contents. In addition, a container exceeding 4 fluid ounces volumetric capacity (7.22 cubic inches) or containing more than 65 grams of fuel may not be connected or manifolded to a lighter or similar device and must also be described and packaged according to the fuel contained therein. A Shipper of a hazardous material is responsible for its classification and packaging prior to offering it for shipment to a Carrier. Transportation by vessel in IBCs is prohibited. Portable tank instructions specify the requirements applicable to a portable tank when used for the transportation of a specific hazardous material. B85 Cargo tanks must be marked with the name of the lading in accordance with the requirements of 172.302(b). 127 Mixtures containing oxidizing and organic materials transported under this entry may not meet the definition and criteria of a Class 1 material. Nickel-metal hydride batteries subject to this special provision are subject only to the following requirements: (1) The batteries must be prepared and packaged for transport in a manner to prevent a dangerous evolution of heat, short circuits, and damage to terminals; and are subject to the incident reporting in accordance with 171.16 of this subchapter if a fire, violent rupture, explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other evidence) occurs as a direct result of a nickel metal hydride battery; and (2) when loaded in a cargo transport unit in a total quantity of 100 kg gross mass or more, the shipping paper requirements of Subpart C of this part, the manifest requirements of 176.30 of this subchapter, and the vessel stowage requirements assigned to this entry in Column (10) of the 172.101 Hazardous Materials Table. A11 For combination packagings, when metal inner packagings are permitted, only specification cylinders constructed of metals which are compatible with the hazardous material may be used. This is in response to your November 18, 2015 e-mail and subsequent conversations with members of my staff requesting clarification of the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180) applicable to the selection of a . The articles may be transported as in Division 1.4 Compatibility Group D (1.4D) if all of the conditions specified in 173.63(a) of this subchapter are met. A14 This material is not authorized to be transported as a limited quantity or consumer commodity in accordance with 173.306 of this subchapter when transported aboard an aircraft. The Associate Administrator will base the authorization on results from Series 2 tests and a Series 6(c) test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport in accordance with the requirements of this subchapter. If the SADT of the technically pure substance is higher than 75 C, the technically pure substance and formulations derived from it are not self-reactive materials and, if not meeting any other hazard class, are not subject to the requirements of this subchapter. Use the above summary to assist you in reviewing the special provisions applicable to the HazMat you offer for transportation. 391 Except for articles being transported by motor vehicle as a material of trade in accordance with 173.6 of this subchapter, articles containing hazardous materials of Division 2.3, or Division 4.2, or Division 4.3, or Division 5.1, or Division 5.2, or Division 6.1 (substances with an inhalation toxicity of Packing Group I) and articles containing more than one of the following hazards: (1) Gases of Class 2; (2) Liquid desensitized explosives of Class 3; or (3) Self-reactive substances and solid desensitized explosives of Division 4.1, may only be offered for transportation and transported under conditions approved by the Associate Administrator. The identification number used must be consistent on package markings, shipping papers and emergency response information. These provisions apply only to non-bulk packagings: N3 Glass inner packagings are permitted in combination or composite packagings only if the hazardous material is free from hydrofluoric acid. not more than 0.1 mL/hour per 30 mL inner packaging at 20 C (68 F) produced from gradual decomposition. These articles must be tested in accordance with Test series 6(c) of Part I of the UN Manual of Tests and Criteria (incorporated by reference; see 171.7 of this subchapter), with no explosion of the device, no fragmentation of device casing or pressure vessel, and no projection hazard or thermal effect that would significantly hinder fire-fighting or other emergency response efforts in the immediate vicinity. Column 7: Special Provisions - Specifies codes for special provisions applicable to some hazardous materials. A8 For combination packagings, if glass inner packagings (including ampoules) are used, they must be packed with cushioning material in tightly closed metal receptacles before packing in outer packagings. The total mass of lithium batteries contained in any package must not exceed the quantity limits in columns (9A) and (9B) for passenger aircraft or cargo aircraft, as applicable; b. The capacity of each drum must not exceed 220 L (58 gallons). b. The temperature of the material at the time it is offered for transport and during transportation may not exceed 55 C (130 F). TP8 A portable tank having a minimum test pressure of 1.5 bar (150 kPa) may be used when the flash point of the hazardous material transported is greater than 0 C (32 F). Samples taken at random must withstand the prescribed tests without breakage or leakage. No outage is required for helium. Company Name: Artisan EHS Consulting, LLC. Others such as copper and silver are available in trace amounts. 381 For railroad flagging kits, see 173.184 (c) of this subchapter. The purpose of this article is to explain the meaning of the coding system for the Special Provisions of column 7 in order to facilitate your review and understanding of them and how they may apply to your shipment of a hazardous material. A rocket motor to be considered nonpropulsive must be capable of unrestrained burning and must not appreciably move in any direction when ignited by any means. 166 When transported in non-friable tablet form, calcium hypochlorite, dry, may be transported as a Packing Group III material. (2) A codes. N37 This material may be shipped in an integrally-lined fiber drum (1G) which meets the general packaging requirements of subpart B of part 173 of this subchapter, the requirements of part 178 of this subchapter at the packing group assigned for the material and to any other special provisions of column 7 of the 172.101 table. 5. A212 UN 2031, Nitric acid, other than red fuming, with more than 20% and less than 65% nitric acid intended for use in sterilization devices only, may be transported on passenger aircraft irrespective of the indication of forbidden in columns (9A) of the 172.101 table provided that: a. The objects must be secured to the flat car, motor vehicle, intermodal container, or unitized by steel banding to wooden runners or pallets and the units secured to the flat car, motor vehicle, or freight container to prevent shifting, including relative motion between the objects, under conditions normally incident to transportation. Packages containing mixtures with not less than 90% by mass, of phlegmatizer need not bear a POISON subsidiary risk label. Please do not provide confidential Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. A bulk packaging containing sulfur is not subject to the placarding requirements of subpart F of this part, if it is marked with the appropriate identification number as required by subpart D of this part. 368 In the case of non-fissile or fissile-excepted uranium hexafluoride, the material must be classified under UN3507 or UN2978. c. Packagings are excepted from the design stress limits at elevated temperatures, as described in Section VIII of the ASME Code (IBR, see 171.7 of this subchapter). There must be no hazardous effects outside the package such as disruption of the package, metal fragments or a receptacle which passes through the packaging. Use of these proper shipping names for domestic shipments may be made only under a DOT special permit, as defined in, and in accordance with the requirements of subpart B of part 107 of this subchapter. There you have it! Dry batteries not specifically covered by another entry in the 172.101 Table are covered by this entry (i.e., Batteries, dry, sealed, n.o.s.) While columns 8 and 7 of the Hazardous Materials Table are used to determine authorized packaging for most HazMat (more on that in a little bit), some methods of transportation, HazMat quantities, and specific operations rely on other methods. The letter Z shown in the marking code for composite IBCs must be replaced with a capital code letter designation found in 178.702(a)(2) of this subchapter to specify the material used for the other packaging. B78 Tank cars must have a test pressure of 4.14 Bar (60 psig) or greater and conform to Class 103, 104, 105, 109, 111, 112, 114 or 120. This entry may not be used for solids containing a Packing Group I liquid. In addition, the column 5 reference is modified to read III on those occasions when this material is offered for transportation or transported by highway or rail. Essentially, such SSolder complies with RoHS (Restriction of Hazardous Substances) regulations. Those "other methods" for determining authorized packaging are identified at 173.24 (c) (1) (ii). 59 Ferrocerium, stabilized against corrosion, with a minimum iron content of 10 percent is not subject to the requirements of this subchapter. 150 This description may only be used for ammonium nitrate-based fertilizers. Outage must be at least 5 percent at 98 C (208 F). 171 This entry may only be used when the material is transported in non-friable tablet form or for granular or powered mixtures that have been shown to meet the PG III criteria in 173.127. 172-123, 55 FR 52582, Dec. 21, 1990]. Decomposition can be initiated by heat, moisture or by impurities (e.g., powdered metals (iron, manganese, cobalt, magnesium)). 39 This substance may be carried under provisions other than those of Class 1 only if it is so packed that the percentage of water will not fall below that stated at any time during transport. Each tank car must have a reclosing pressure relief device having a start-to-discharge pressure of 15.51 Bar (225 psig). TP10 A lead lining, not less than 5 mm thick, which shall be tested annually, or another suitable lining material approved by the competent authority, is required. 325 In the case of non-fissile or fissile-excepted uranium hexafluoride, the material must be classified under UN 2978. 38 If this material shows a violent effect in laboratory tests involving heating under confinement, the labeling requirements of Special Provision 53 apply, and the material must be packaged in accordance with packing method OP6 in 173.225 of this subchapter. B133 Hydrochloric acid concentration not exceeding 38%, in Packing Group II, is authorized to be packaged in UN31H1 or UN31HH1 intermediate bulk containers when loaded in accordance with the requirements of 173.35(h) of this subchapter. N36 Aluminum or aluminum alloy construction materials are permitted only for halogenated hydrocarbons that will not react with aluminum. Interior heating coils are not authorized. Transportation of these packages also requires the door of each van trailer to be marked with Warning trailer may contain chemical vapor. If chemical stabilization becomes ineffective at lower temperatures within the anticipated duration of transport, temperature control is required and is forbidden by aircraft. The tank must have been designed and constructed to be capable of withstanding full vacuum. In addition, MC 312 and DOT 412 cargo tank motor vehicles must: a. 32 Polymeric beads and molding compounds may be made from polystyrene, poly(methyl methacrylate) or other polymeric material. Column 7 contains special provisions associated with the hazardous material. For UN 3176, this requirement only applies when the hazardous material reacts dangerously with water. A4 Liquids having an inhalation toxicity of Packing Group I are not permitted on aircraft. Column 7: Special provisions. A101 In addition to the applicable requirements of 173.185, the quantity of lithium metal in the batteries contained in any piece of equipment must not exceed 12 g per cell and 500 g per battery. However, sediments remaining in the tank that meet the definition for a hazardous material are subject to the applicable regulations of this subchapter. 163 Substances must satisfactorily pass Test Series 8 of the UN Manual of Tests and Criteria, Part I, Section 18 (IBR, see 171.7 of this subchapter). Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. 106 The recognized name of the particular explosive may be specified in addition to the type. Column 8 121 This substance, when containing less alcohol, water or phlegmatizer than specified, may not be transported unless approved by the Associate Administrator. (7) A code containing the letter T refers to a special provision which applies only to transportation in UN or IM Specification portable tanks. 173 For adhesives, printing inks, printing ink-related materials, paints, paint-related materials, and resin solutions which are assigned to UN3082, and do not meet the definition of another hazard class, metal or plastic packaging for substances of packing groups II and III in quantities of 5 L (1.3 gallons) or less per packaging are not required to meet the UN performance package testing when transported: a. A35 This includes any material which is not covered by any of the other classes but which has an anesthetic, narcotic, noxious or other similar properties such that, in the event of spillage or leakage on an aircraft, extreme annoyance or discomfort could be caused to crew members so as to prevent the correct performance of assigned duties. A hypochlorite solution, UN1791, is a Class 8 corrosive material. Be ASME Code (U) stamped for 100% radiography of all pressure-retaining welds; b. It must be demonstrated that the article relieves its pressure by means of a fire degradable seal or other pressure relief device, in such a way that the pressure receptacle will not fragment and that the article or fragments of the article do not rocket more than 10 meters; and. N45 Copper cartridges are authorized as inner packagings if the hazardous material is not in dispersion. A37 This entry applies only to a material meeting the definition in 171.8 of this subchapter for self-defense spray. Have accident damage protection which conforms with 178.345-8 of this subchapter; c. Have a MAWP or design pressure of at least 87 psig: and. If you have questions for the Agency that issued the current document please contact the agency directly. Multiple provisions can be listed in this column. Unlined tanks must be passivated before being placed in service. Openings for safety relief devices on multi-unit tank car tanks shall be plugged or blank flanged. This entry may not be used for ammonium nitrate for which a proper shipping name already exists in the 172.101 Hazardous Materials Table, including ammonium nitrate mixed with fuel oil or any other commercial grade of ammonium nitrate (e.g., ammonium nitrate fertilizer). Unfortunately, the amendments to the table entries for various hazardous materials introduced new unintended errors that PHMSA is correcting in this notice. B15 Packagings must be protected with non-metallic linings impervious to the lading or have a suitable corrosion allowance. Tank car tanks must have a test pressure rating of 1,379 kPa (200 psig). (3) A flammable gas is a gas that meets the criteria in 173.115 of this subchapter. (7) The design type of the article must be subjected to the following test. 172-29, 41 FR 15996, Apr. 151 If this material meets the definition of a flammable liquid in 173.120 of this subchapter, a FLAMMABLE LIQUID label is also required and the basic description on the shipping paper must indicate the Class 3 subsidiary hazard. 74 During transport, this material must be protected from direct sunshine and stored or kept in a cool and well-ventilated place, away from all sources of heat. If unlined tanks are washed out with water, they must be repassivated prior to return to service. b. B13 A nonspecification cargo tank motor vehicle authorized in 173.247 of this subchapter must be at least equivalent in design and in construction to a DOT 406 cargo tank or MC 306 cargo tank (if constructed before August 31, 1995), except as follows: a. Packagings equivalent to MC 306 cargo tanks are excepted from the certification, venting, and emergency flow requirements of the MC 306 specification. Portable tank special provisions are designated with the abbreviation TP (tank provision) and are assigned to specific hazardous materials in Column (7) of the 172.101 Table. Column 5 references applicable requirements for bottom openings in part 178 of this subchapter. It may not be used to describe articles, machinery, or apparatus for which a proper shipping name exists in the 172.101 Table. Test of type 3(c) is not required. Additionally, the offeror must notify the carrier if the tank pressure rise exceeds 3 psig over any 24-hour period. B80 Each cargo tank must have a minimum design pressure of 276 kPa (40 psig). The pressure relief device must be preceded by a frangible disk in accordance with the requirements in 178.275(g)(3) of this subchapter to prevent crystallization of the product in the pressure relief device. For other than Class 7 or the DANGEROUS . 181 When a package contains a combination of lithium batteries contained in equipment and lithium batteries packed with equipment, the following requirements apply: a. 12 In concentrations greater than 40 percent, this material has strong oxidizing properties and is capable of starting fires in contact with combustible materials. Except for transportation by aircraft, in palletized loads, a pallet box or unit load device (e.g. Packagings of other material constructed with a small amount of metal must be designed such that the hazardous material does not contact the metal. Hazardous materials shipped under this entry are excepted from the labeling requirements of this subchapter unless offered for transportation or transported by aircraft and are not subject to the placarding requirements of subpart F of this part. the hierarchy of the document. (iii) T50 When portable tank instruction T50 is indicated in Column (7) of the 172.101 Hazardous Materials Table, the applicable liquefied compressed gas and chemical under pressure descriptions are authorized to be transported in portable tanks in accordance with the requirements of 173.313 of this subchapter. The present arrangement occurs in such a way that one QA molecule is hydrogen-bonded to four neighboring molecules: two different molecules in one column and other two molecules in another column. B115 Rail cars, highway trailers, roll-on/roll-off bins, or other non-specification bulk packagings are authorized. The batteries inside the cargo transport unit are not subject to marking or labelling requirements of part 172 subparts D and E of this subchapter. Packagings may include a vent to permit the slow escape of gas (i.e. Refrigerated liquefied gases that are authorized to be transported in portable tanks are specified in tank instruction T75. (2) To the extent a special provision imposes limitations or additional requirements on the packaging provisions set forth in column 8 of the 172.101 table, packagings must conform to the requirements of the special provision. It is shown that it does not pose a significant risk in transportation; b. Interpretation Response Details. Primary receptacles must conform to the general packaging requirements of subpart B of part 173 of this subchapter and may not leak. 3090 or 3091, as appropriate. Shipping papers at all times must reflect a correct current accounting of all cylinders both full and expended. This training must be documented in training records required by 172.704(d). Quantities of not more than 500 g per package with not less than 10 percent water by mass may also be classed in Division 4.1, provided a negative test result is obtained when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). TP7 The vapor space must be purged of air by nitrogen or other means. c. The completed package must meet the Packing Group II performance level, as applicable for combination packagings with a plastic box outer packaging, in accordance with subpart M of part 178 of this subchapter. Further, the limitations and/or additional requirements found in the special provisions of column 7 will supersede the packaging authorizations of column 8 of the Hazardous Materials Table. You can (3) The total amount of gas from all detectors per outer packaging must not exceed 52 grams (1.83 ounces). 168 For lighters containing a Division 2.1 gas (see 171.8 of this subchapter), representative samples of each new lighter design must be examined and successfully tested as specified in 173.308(b)(3).
Why Did The Cleveland Show Get Cancelled, Xylophone Sounds In Words, Zsuzsi Starkloff Age Difference, What Is The Difference Between Section 17 And Section 47, Articles C
Why Did The Cleveland Show Get Cancelled, Xylophone Sounds In Words, Zsuzsi Starkloff Age Difference, What Is The Difference Between Section 17 And Section 47, Articles C